*************************************************** bootloader *********************************************************** U-Boot 1.1.3 (Apr 16 2009 - 10:03:22) Board: Ralink APSoC DRAM: 32 MB relocate_code Pointer at: 81fa8000 **************************** Init GPIO Pin**************************** flash_protect ON: from 0xBFC00000 to 0xBFC262B7 protect on 0 protect on 1 protect on 2 protect on 3 protect on 4 protect on 5 protect on 6 protect on 7 protect on 8 protect on 9 flash_protect ON: from 0xBFC30000 to 0xBFC3FFFF protect on 10 *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 3.1 -------------------------------------------- ASIC 3052_MP1 (MAC to GigaMAC Mode) DRAM COMPONENT: 256Mbits DRAM BUS: 16BIT Total memory: 32 MBytes Flash: 4 MBytes Date:Apr 16 2009 Time:10:03:22 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:128, ways:4, linesz:32 ,total:16384 ##### The CPU freq = 320 MHZ #### SDRAM bus set to 16 bit SDRAM size =32 Mbytes Please choose the operation: 0: Load ucos code to SDRAM via TFTP Client. 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 9: Load Boot Loader code then write to Flash via TFTP. Net: eth_register Eth0 (10/100-M) enetvar=ethaddr,Eth addr:00:AA:BB:CC:DD:18 00:AA:BB:CC:DD:18: eth_current->name = Eth0 (10/100-M) DEBUG BootType=48 0: System Load Boot Loader | F/W then write to Flash via TFTP Client. Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Please Input new ones /or Ctrl-C to discard Input device IP (10.10.10.123) Input server IP (10.10.10.3) Input Li nux Kernel filename () netboot_common, argc= 3 *************buf = 0x81fce420 **********NexTxPacket = 81fe64c0 NetTxPacket = 0x81FE64C0 NetRxPackets[0] = 0x81FE6AC0 NetRxPackets[1] = 0x81FE70C0 NetRxPackets[2] = 0x81FE76C0 NetRxPackets[3] = 0x81FE7CC0 NetRxPackets[4] = 0x81FE82C0 NetRxPackets[5] = 0x81FE88C0 NetRxPackets[6] = 0x81FE8EC0 NetRxPackets[7] = 0x81FE94C0 NetRxPackets[8] = 0x81FE9AC0 NetRxPackets[9] = 0x81FEA0C0 NetRxPackets[10] = 0x81FEA6C0 NetRxPackets[11] = 0x81FEACC0 NetRxPackets[12] = 0x81FEB2C0 NetRxPackets[13] = 0x81FEB8C0 NetRxPackets[14] = 0x81FEBEC0 NetRxPackets[15] = 0x81FEC4C0 NetRxPackets[16] = 0x81FECAC0 NetRxPackets[17] = 0x81FED0C0 NetRxPackets[18] = 0x81FED6C0 NetRxPackets[19] = 0x81FEDCC0 KSEG1ADDR(NetTxPacket) = 0xA1FE64C0 NetLoop,call eth_halt ! NetLoop,call eth_init ! Trying Eth0 (10/100-M) Waitting RT2880_RX_DMA_BUSY status Start... done Mac to giga Mac mode rx_ring = A1FCE840, tx_ring0 = A1FCE700 Header Payload scatter function is Disable !! RT2880_PDMA_GLO_CFG=00000020 ************************************************* RT2880_RX_CALC_IDX0=19 RT2880_RX_DRX_IDX0 = 0 ************************************************* ETH_STATE_ACTIVE!! Select server or client model: 1/2 server model start SERVER IP address : 192.168.1.6 port:69 Load address: 0x80100000 Loading: * *************************************************** normalny start *********************************************************** U-Boot 1.1.3 (Apr 16 2009 - 10:03:22) Board: Ralink APSoC DRAM: 32 MB relocate_code Pointer at: 81fa8000 **************************** Init GPIO Pin**************************** flash_protect ON: from 0xBFC00000 to 0xBFC262B7 protect on 0 protect on 1 protect on 2 protect on 3 protect on 4 protect on 5 protect on 6 protect on 7 protect on 8 protect on 9 flash_protect ON: from 0xBFC30000 to 0xBFC3FFFF protect on 10 *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 3.1 -------------------------------------------- ASIC 3052_MP1 (MAC to GigaMAC Mode) DRAM COMPONENT: 256Mbits DRAM BUS: 16BIT Total memory: 32 MBytes Flash: 4 MBytes Date:Apr 16 2009 Time:10:03:22 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:128, ways:4, linesz:32 ,total:16384 ##### The CPU freq = 320 MHZ #### SDRAM bus set to 16 bit SDRAM size =32 Mbytes Please choose the operation: 0: Load ucos code to SDRAM via TFTP Client. 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 9: Load Boot Loader code then write to Flash via TFTP. You choosed 3 0 3: System Boot system code via Flash. ## Booting image at bfc50000 ... Bad Magic Number,43535953 Image Name: Linux Kernel Image Created: 2009-11-03 9:38:24 UTC System Control Status = 0x20400000 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 3653548 Bytes = 3.5 MB Load Address: 80000000 Entry Point: 802bc000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 802bc000) ... ## Giving linux memsize in MB, 32 Starting kernel ... LINUX started... THIS IS ASIC Linux version 2.6.21 (root@vance.localdomain) (gcc version 3.4.2) #142 Tue Nov 3 17:30:33 CST 2009 The CPU feqenuce set to 320 MHz CPU revision is: 0001964c Determined physical RAM map: memory: 02000000 @ 00000000 (usable) Built 1 zonelists. Total pages: 8128 Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4 Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). Cache parity protection disabled cause = 80800034, status = 1100ff00 PID hash table entries: 128 (order: 7, 512 bytes) calculating r4koff... 00138800(1280000) CPU frequency 320.00 MHz Using 160.000 MHz high precision timer. Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 29468k/32768k available (2266k kernel code, 3300k reserved, 529k data, 1 16k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Time: MIPS clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher squashfs: LZMA suppport for slax.org by jro io scheduler noop registered (default) FLASH_API: MAN_ID=C2 DEV_ID=22A8 SIZE=4MB ***********Init LED Driver***************** Init GPIO Pin Init GPIO Direction Init GPIO Interrupt ***********Init LED Driver Finishing***************** Ralink_gpio_init_irq LED & GPIO & LAN Status Driver LED_VERSION HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096 N_HDLC line discipline registered. Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A loop: loaded (max 8 devices) rdm_major = 254 GDMA1_MAC_ADRH -- : 0x00000000 GDMA1_MAC_ADRL -- : 0x00000000 Ralink APSoC Ethernet Driver Initilization. v1.60 256 rx/tx descriptors allocat ed, mtu = 1500! GDMA1_MAC_ADRH -- : 0x0000000c GDMA1_MAC_ADRL -- : 0x43305277 PROC INIT OK! PPP generic driver version 2.4.2 PPP BSD Compression module registered NET: Registered protocol family 24 ralink flash device: 0x1000000 at 0xbf000000 Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. Creating 7 MTD partitions on "Ralink SoC physically mapped flash": 0x00000000-0x00030000 : "Bootloader" mtd: Giving out device 0 to Bootloader 0x00030000-0x00040000 : "Config " mtd: Giving out device 1 to Config 0x00040000-0x00050000 : "Factory" mtd: Giving out device 2 to Factory 0x00050000-0x00160000 : "Kernel" mtd: Giving out device 3 to Kernel 0x00160000-0x003e0000 : "RootFS" mtd: Giving out device 4 to RootFS 0x003e0000-0x00400000 : "Cimage" mtd: Giving out device 5 to Cimage 0x00050000-0x003e0000 : "Uimage" mtd: Giving out device 6 to Uimage block2mtd: version $Revision: 1.1.1.1 $ usbcore: registered new interface driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver dwc_otg: version 2.60a 22-NOV-2006 DWC_otg: Using DMA mode dwc_otg lm0: DWC OTG Controller dwc_otg lm0: new USB bus registered, assigned bus number 1 dwc_otg lm0: irq 18, io mem 0x00000000 DWC_otg: Init: Port Power? op_state=1 DWC_otg: Init: Power Port (0) usb usb1: Product: DWC OTG Controller usb usb1: Manufacturer: Linux 2.6.21 dwc_otg_hcd usb usb1: SerialNumber: lm0 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected u32 classifier Performance counters on nf_conntrack version 0.5.0 (256 buckets, 2048 max) ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone ClusterIP Version 0.8 loaded successfully arp_tables: (C) 2002 David S. Miller ipt_time loading TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 116k freed init started: BusyBox v1.11.1 (2009-11-03 17:37:25 CST) starting pid 606, tty '': '/etc/rc.sh' Cannot run '/etc/rc.sh': No such file or directory starting pid 607, tty '': '-/bin/sh'console. Algorithmics/MIPS FPU Emulator v1.5 BusyBox v1.11.1 (2009-11-03 17:37:25 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. Sat Jan 1 00:00:00 UTC 2000 killall: pptp.sh: no process killed killall: pppoe.sh: no process killed killall: failover.sh: no process killed ifconfig: 0.0.0.0: error fetching interface information: Device not found phy_tx_ring = 0x01d25000, tx_ring = 0xa1d25000, size: 16 bytes phy_rx_ring = 0x01d26000, rx_ring = 0xa1d26000, size: 16 bytes RT305x_ESW: Link Status Changed GDMA1_FWD_CFG = 710000 ra2880stop()...Done Free TX/RX Ring Memory! GDMA1_MAC_ADRH -- : 0x0000001f GDMA1_MAC_ADRL -- : 0x1f6d80fc phy_tx_ring = 0x01cdb000, tx_ring = 0xa1cdb000, size: 16 bytes phy_rx_ring = 0x01cdc000, rx_ring = 0xa1cdc000, size: 16 bytes GDMA1_FWD_CFG = 710000 eth2.1: Setting MAC address to 00 1f 1f 6d 80 fc. VLAN (eth2.1): Underlying device (eth2) has same MAC, not checking promiscious mode. eth2.2: Setting MAC address to 00 0f ea c4 35 3c. device eth2 entered promiscuous mode VLAN (eth2.2): Setting underlying device (eth2) to promiscious mode. Initialize WLAN interface Setup BRIDGE interface ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device bridge br0 doesn't exist; can't delete it Setup bridge... device eth2.1 entered promiscuous mode eth2.1: dev_set_promiscuity(master, 1) route: ioctl 0x890c failed: No such process br0: port 1(eth2.1) entering learning state br0: topology change detected, propagating br0: port 1(eth2.1) entering forwarding state route: ioctl 0x890c failed: No such process route: ioctl 0x890c failed: No such process ------> 802.1x--------->Enter ------> 802.1x------>Exit Static DHCP Leases disable! route: ioctl 0x890c failed: No such process device eth2 is not a slave of br0 device eth2.1 is already a member of a bridge; can't enslave it to bridge br0. switch reg write offset=14, value=405555 switch reg write offset=50, value=2001 switch reg write offset=98, value=7f3f switch reg write offset=40, value=1001 switch reg write offset=44, value=1001 switch reg write offset=48, value=1002 switch reg write offset=70, value=ffff506f Set: phy[0].reg[0] = b100 Set: phy[1].reg[0] = b100 Set: phy[2].reg[0] = b100 Set: phy[3].reg[0] = b100 Set: phy[4].reg[0] = b100 ********************************************************************** * Running Diagd * ********************************************************************** ********************************************************************** * Enable WSC_UPnP * ********************************************************************** /bin/init.sh: line 522: wscd: not found ********************************************************************** * Enable LLTD * ********************************************************************** killall: snmpd: no process killed killall: lld2d: no process killed ********************************************************************** * Enable GPIO Interrupt * ********************************************************************** ralink_gpio:ioctl GPIO REG ralink_gpio:ioctl GPIO REG killall: watchdog.sh: no process killed ip_table: set wan_name=eth2.2 killall: radiusd: no process killed RADIUS server disable !! kill: you need to specify whom to kill ********************************************************************** * FREE Page,Dentries and Inodes Cache * ********************************************************************** MemFree: 23608 kB Cached: 1340 kB killall: pppd: no process killed killall: pptp.sh: no process killed killall: pppoe.sh: no process killed ifconfig: 0.0.0.0: error fetching interface information: Device not found Setup WAN interface ifconfig: 0.0.0.0: error fetching interface information: Device not found device eth2 is not a slave of br0 device eth2.1 is already a member of a bridge; can't enslave it to bridge br0. switch reg write offset=14, value=405555 switch reg write offset=50, value=2001 switch reg write offset=98, value=7f3f switch reg write offset=40, value=1001 switch reg write offset=44, value=1001 switch reg write offset=48, value=1002 switch reg write offset=70, value=ffff506f Set: phy[0].reg[0] = b100 Set: phy[1].reg[0] = b100 Set: phy[2].reg[0] = b100 Set: phy[3].reg[0] = b100 Set: phy[4].reg[0] = b100 udhcpc (v1.11.1) started rm: cannot remove '/tmp/agentenabledflag': No such file or directory /bin/start_wan.sh: line 265: /bin/agent: nip_table: set wan_name=eth2.2 ot found killall: modemctl: no process killed ralink_gpio:ioctl GPIO REG ralink_gpio:ioctl GPIO REG into eth2.2.deconfig killall: snmpd: no process killed